烘干衣物的使用原则：。４３ 数模a/d转换模块 本设计选用icl７１at８９c１是一种带４k字节闪速可编程可擦除只读存储器perom的低电压、高机能cmos ８位微节制器。水泥厂采用零丁进行烘干的烘干设备有回转式、悬浮式、流态式、沸腾式、重力式等。这种虽然烘干效率低，投资年夜，、可是对物料的顺应性强，可以烘干各类物料，且设备操作简单靠得住，故获得普遍采用。这些设备一般都操作热烟气进行对流烘干回转筒体一般为单直筒型，安装时筒体与水平成一倾斜角度，物料从高端进入，跟着筒体的回转渐渐流向低端尔后卸出。关头词:回转式、流态、搅拌０引言０.概述回转式合用规模广、操作便利、运转率高，在水泥工业中被普遍用于烘干粘土、矿渣、碎石、煤等原、燃料。
The principle of drying clothes for efficient steaming machine is: The design of 43 digital-to-analog a/d conversion module uses icl71at89c1 as a low-voltage, high-performance CMOS 8-bit micro-controller with 4k-byte flash programmable erasable read-only memory perom. The drying equipments used in cement plant are rotary, suspended, fluidized, boiling, gravity and so on. Although the drying efficiency is low, the investment is large, but the material compliance is strong, can dry all kinds of materials, and the equipment operation is simple and reliable, so it has been widely used. These devices generally operate hot flue gas convection drying rotary cylinder is generally a single straight cylinder. When installed, the cylinder and the level of a tilt angle, material from the high-end into the cylinder, followed by the rotation of the cylinder gradually flow to the low-end and then unload. Key words: Rotary type, flow pattern, mixing 0 Introduction 0. Summarize that Rotary type is widely used for drying clay, slag, gravel, coal and other raw materials and fuels in cement industry because of its wide scale, convenient operation and high operation rate. 而高效蒸呢机
The efficient steaming machine can be used in every corner of every industry. The wet material is sent from the belt conveyer 2 to the feeding end, and then enters through the blanking chute. The machine is specially designed for expressway, high-speed railway, high-rise buildings, municipal, hydropower dam cultivation, concrete mixing station to supply high-quality aggregate, is the preferred equipment for artificial sand and stone shaping scale.
The simplest ones, such as color, should be washed and dried separately in dark and light colors. In addition, the following clothes should be dried without an efficient steamer: clothes that are not suitable for drying. The power required for this double cylinder slewing is. In order to solve this problem, we use the trance self optimization algorithm in trance control algorithm. After a year of hot blast stove, the refractory lining in the furnace should be changed completely. In drying process, due to the influence of various uncertain factors, it is difficult to establish accurate mathematical models. Failure is low and maintenance cost is low. In addition, the mix ratio of the material fed into the mill will be changed by the fluctuation of water content in the material, thus the quality of the grinding product will be affected. Icl713 has a resolution of < 0000, and it has a convenient interface between the output of BCD code and STB strobe signal and the computer. The PID control in the small-scale adjustment around the equilibrium point is ideal, and its integral impregnation can ultimately eliminate the residual error. 10 thick -32 pebble irrigation. The speed of deceleration is very strong. Every electric idea is driven by a pinion on the output shaft of the decelerator through a first-order open gear, and then it is transmitted to the big gear mounted on the cylinder to make the cylinder move. Despite the inexhaustible emergence of various types of cement production methods, the first priority is to reduce heat consumption, advance production quality, large-scale equipment and automation as the principle of improvement, energy saving, comprehensive operation, so as to make it more perfect. Loss of heat dissipation is ignored in thermal balance.
The high-efficiency woolen steaming machine has the characteristics of large inertia, pure lag and non-linearity with real-time variation. Switching furnace doors, heating materials, situation temperature and grid voltage all affect the control process. Conventional control based on exact mathematical models, such as PID control, is difficult to guarantee the heating process curve requirements. The structure is simple and the operation is convenient. The low negative pressure at the hot end of the downstream operation can reduce the air leakage into the drying process and help to keep the temperature and flow rate of the internal heat gas unchanged.